Grisham 42021 Installationsanleitung PDF herunterladen

SCREEN PANEL

TEMPERED

GLASS PANEL

HINGE SIDE Z BAR

STORM CHAIN

RAIN CAP

HEADER

LATCH SIDE Z BAR

CLOSER

EXPANDER BAR

DOUBLE WEATHER

STRIPPED SWEEP

Lock Bar Plate

TOOLS REQUIRED:

• Electric Drill

• Hammer

• Hack Saw

• 3/8" Wood Chisel

• 5/32" Drill Bit

• Phillips Head Screw Driver

• Flat Head Screw Driver

For Questions Concerning This Product

Phone - 1-800-238-1005

MAINTENANCE GUIDE

FINISH

HINGES

GLASS CLIPS

PARTS

CLOSER

Grisham Bros.

WARRANTY INFORMATION

INSTALLATION, MAINTENANCE, & WARRANTY

Your steel security system storm door will look beautiful much longer by following these simple procedures. Once or twice a year, apply a coat of

Armor All or similar product to help retain the finish luster and protect against ultra-violet deterioration. All steel products exposed to weather can rust.

Periodically, inspect your door for scratches or abrasions on the painted surface. If any are found, sand surface, if necessary, and touch up with paint

immediately.

Lubricate the hinges should a squeak develop.

Be sure that the glass panel clips are only hand tight. Over tightening can cause the glass clips to break. If any are loose, simply tighten with a Phillips

head screwdriver.

To keep all parts looking new, use any good cleaner. Frequency may depend on how severe the weather is in your area. A once a year cleaning and

polishing is sufficient in most areas. Also, check the handle to be sure the set screw is still tightly secured; if not, tighten it back down with a screw driver.

Check closer action about twice a year. Open the door a few times and let it close by itself so that you can see whether or not the closer tension should be

increased or decreased for smoothest operation. The adjustment screw is located at the end of the closer cylinder. Unscrew the adjustment screw to

decrease tension; screw it in more tightly to increase tension. To fine tune the adjustment screw, make adjustments in quarter-turns until you find the

optimum adjustment.

In the event that our products or any parts thereof should prove to be defective in material or workmanship, under normal use and service, and such defects

are reported to us within (1) one year from the date of shipment, and at our option, we will repair or replace whatever is necessary to eliminate the defect or

refund the purchase price of such parts in lieu of furnishing a replacement. We assume no responsibility for incidental or consequential damages arising

from defective products; nor do we assume any responsibility for failures, breakage, or cost that result from abuse, abnormal use, misuse, negligence,

accident, exposure to corrosive fumes, condensates, fire or damage as a result of improper installation. This warranty does not apply to screen or glass.

Except as stated above, we make no warranties, either expressed or implied, as to any matter whatsoever, including without limitations, the condition of

our products, their merchantability or fitness for any particular purpose. We assume no other expenses such as labor cost of any kind for removal,

replacement of parts, repairs or installation.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - Grisham Bros

SCREEN PANELTEMPEREDGLASS PANELHINGE SIDE Z BAR STORM CHAINRAIN CAP HEADER LATCH SIDE Z BARCLOSEREXPANDER BAR DOUBL

Seite 2 - For 400 and 500 Series Doors

1. Measure the height of the opening where the door isto be installed.2. 3. Place the door into the opening making sure it is leveledand plumb. 7.

Seite 3 - HINGE SIDE CONVERSION

HINGE SIDE CONVERSION3/163/161. 2. 3. 5. 13. 4. With the door open, fit the expander bar onto the bottom of the doo

Seite 4 - LOCK BAR COVER INSTALLATION

ScrewScrewLOCK BAR COVER INSTALLATION For 400 and 500 Series DoorsThe lock bar plate is provided to cover the passage slots on the strike side

Seite 5

SCREEN PANELTEMPEREDGLASS PANELBARRA Z DE LADO DE BISAGRACADENA DE TORMENTACABECERA DETAPA CONTRA LLUVIABARRA Z DEL LADO DE PESTILLOCIERREBARRIDO DE

Seite 6 - Instrucciones de instalación:

1. Medir la altura de la abertura por donde la puerta se va a instalar.2. 3. Coloque la puerta en la abertura y asegúrese de que esté niveladay plo

Seite 7

CONVERSIÓN DEL LADO DE BISAGRA3/163/161. 2. 3. 5. 13. 4. Con la puerta abierta, colocar el expansor barra en la par

Seite 8 - Tornillo

Las puertas de la serie 400 y 500TornilloTornillo INSTALACIÓN DE LA PROTECCIÓN DE BLOQUEOLa barra de bloqueo de exposición para sufragar el paso las r

Kommentare zu diesen Handbüchern

Keine Kommentare

Grisham 42021 Installationsanleitung

Stöbern Sie online oder laden Sie Installationsanleitung nach Garagentor-Öffner Grisham 42021 herunter. Grisham 42021 Installation Guide Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern